Aluminium radiators type ARMAT PLUS

Aluminium radiators type ARMAT plus offer comfort solution for building heating. The main construction element is a block with 3 cells. These blocks are mounted into sets with the use of one or two cells in the way to achieve the most exactly required performance of the body according to customer requirements. At the same time with arbitrary amount of cells it is also practically possible to arbitrary change their height. Basic series of radiators is produced with mounting holes spacing h- 160 until 1800 mm. Thanks to the same construction of bottom and lower part of the cells it is possible to install the body without adjustments as left and right (by turning the body). In order to prevent the danger of point corrosion creation, the aluminium profile is bedded with special thin walled pipe so there is no contact with the heating medium

Use

• For all types of hot water system of etage and central heating.
• Maximal operating temperature 110°C
• Guaranteed operating pressure 0,6 MPa
• Required value of heating water pH 6,5-7,5

Product advantages

1. all aluminium design (AI profile protected by thin wall steel pipe)

• excellent lifetime
• high heating conductivity
• low weight (easy manipulation)

2. construction solution

• chimney construction of the cells assures higher air circulation
• extremely large heating area
• minimal amount of water in the cells

3. product design

• modern appearance
• round shapes minimalising the risk of injuries
• large colour scale

Technical solution of the product allows, according to high cells performance, to achieve fair purchase and operation costs.

Warning

At the use of plastic or copper circuits it is necessary to add to the heating system corrosion inhibitor for aluminium (for example Velcor AL that is supplied by producer). When using steel circuits this inhibitor is not necessary, but producer recommends it.

Quantisation of Velcoru AL:

• Steel or copper circuits 1:100
• Plastic circuits 1:50

At mounting of radiator roses it is not allowable to use cannabis or Teflon tape. Use sealing supplied by producer.

Technical parameters of ARMAT PLUS

type	h	H	Heating area SL	Cell weight	Amount of water	Standard operation status tw1 / tw2, ti (ºC) 90/70/20  75/65/20  55/45/20
	mm	mm	m2	kg	l	Qn1[W]	Q2[Wm]	Qn1[W]	Qm[Wm-1]	Qn1[W]	Qm[Wm-1]
Armat-160	160	200	0,104	0,61	0,33	71	881	56	700	28	351
Armat-200	200	240	0,127	0,67	0,35	82	1018	65	812	33	405
Armat-350	350	390	0,213	0,92	0,39	120	1494	95	1187	48	594
Armat-500	500	540	0,298	1,17	0,43	156	1931	122	1525	62	768
Armat-600	600	640	0,355	1,33	0,46	178	2208	140	1750	71	878
Armat-850	850	890	0,496	1,73	0,54	231	2865	181	2263	92	1140
Armat-900	900	940	0,525	1,82	0,56	241	2991	189	2362	96	1190
Armat-1000	1000	1040	0,582	1,98	0,58	261	3240	205	2563	104	1289
Armat-1200	1200	1240	0,697	2,30	0,64	300	3723	235	2938	119	1481
Armat-1500	1500	1540	0,869	2,80	0,73	355	4417	279	3488	141	1757
Armat-1800	1800	1840	1,041	3,28	0,82	409	5084	321	4013	162	2022

Note

thermal power for the heat substance (water) and resistance to overpressure was changed in HLK Stuttgart (Germany) according to DIN EN 442-1,2,3
tw1 - the water temperature at the inlet
tw2 - water temperature at the outlet
ti - reference temperature of air
Qn1 - nominal thermal performance of the cell, obtained as the arithmetic average of the performance of the body of 10 cells in the basic operation status
Qm - thermal module in the meaning of ČSN 061101 (thermal power of the body with length I = 1 m)